Quote from Leteen on April 27, 2025, 4:58 am

Hi guys, awesome project!! I’m interested in modifying some of the files to fit local parts, so far I’ve used blender to fit 16x5x5 and flanged 16x8x5 bearings in the differential, I haven’t finished the whole build but the diff works wonderfully…
I will also be using 16x5x5 bearings for the wheels if possible… I had a ton of these bearings since I dissassembled my Ender 3 Pro and they have 2 of these per POM wheel. I also would like to tune a bit the wheel caster, camber and toe.

I created the account after I purchsaed the Destiny chassis, not sure if there is any way to link the purchase with my account now, I used the same email for both

Quote from Szilard on April 27, 2025, 11:44 am

Hi Leteen!

Very nice modification, this way probably becomes more robust! That is the common benefit “When something is scaled up in this “art”…
I think I added your purchase to your account, so there you have it… 😉

Please whatever you are putting together, do not forget to brag about it!!! THX  

Quote from cordial ripper on July 13, 2025, 11:36 pm

Hello all,

I am new to RC cars and still a newbie in the 3D printing. 

I bought Destiny with the purpose of creating a design of my personal car, as it is a very low limited car that not even diecasts are made. 

Ofc I did not create an account when I bought it because I don’t think ahead so my purchase is not linked to my account either 🙂 silly me

I am still In the middle of building it and I am not so sure how much time will pass until I finish but so far this is my progress in the pictures bellow.

i have made a slight alterations to the steering side bar, for me whatever printer setting I was using the bar was still coming out so I got creative. I added the alteration file in the zip. i leave it to the owner to decide if it’s good or bad 🙂 

cheers

 

Quote from antibala on July 14, 2025, 8:22 am

Hello,

thank for sharing your design.

Could you please share it in STL format ? I tried to convert it to stl but it not worked.

Thank you.

Balázs

Quote from cordial ripper on July 14, 2025, 8:26 am

Hi, of course

 

 

Quote from antibala on July 15, 2025, 9:25 am

Thanks !

Quote from Sally on August 24, 2025, 4:58 pm

Hi, I’m back with an update on my experience with the frame and my fully 3D-printed differential. Over the past few months, I’ve stress-tested it and, to my surprise, there are absolutely no signs of wear on the gears. That’s probably because I packed it full of grease, but hey, if it works, it works.

I also found a Porsche body on MakerWorld that fit perfectly. Overall, I’ve had a great experience with the frame, especially when it comes to modularity and ease of repair. I’m planning to build the Infinity frame once it’s a bit more polished.

I’ve attached the Fusion file for the differential, which also includes some replicated parts from the STLs. I’ve also added a few photos of the body and the frame.

Fusion file and photos

Quote from antibala on August 25, 2025, 8:47 am

Hello Kelpik,

Thank you for sharing your experiences, the file, and the photos. The Porsche looks really awesome!

Best regards,

Balázs

Quote from kevman1 on August 28, 2025, 3:46 pm

Quote from Sally on August 24, 2025, 4:58 pm

Hi, I’m back with an update on my experience with the frame and my fully 3D-printed differential. Over the past few months, I’ve stress-tested it and, to my surprise, there are absolutely no signs of wear on the gears. That’s probably because I packed it full of grease, but hey, if it works, it works.

I also found a Porsche body on MakerWorld that fit perfectly. Overall, I’ve had a great experience with the frame, especially when it comes to modularity and ease of repair. I’m planning to build the Infinity frame once it’s a bit more polished.

I’ve attached the Fusion file for the differential, which also includes some replicated parts from the STLs. I’ve also added a few photos of the body and the frame.

Fusion file and photos

I like the battery holder on the side do you have an STL for that ? Is there a holder for the EsC as well ?

Quote from Sally on August 28, 2025, 3:55 pm

Quote from kevman1 on August 28, 2025, 3:46 pm

 

I like the battery holder on the side do you have an STL for that ? Is there a holder for the EsC as well ?

The battery holder is in the fusion file, as for the esc holded i dont have the file since i got rid of it a long time ago or it’s also in the file.

Quote from kevman1 on August 28, 2025, 10:39 pm

 I can’t open the fusion file unfortunatly, my Fusion is crashing with unable to login error.

Quote from Sally on August 28, 2025, 10:47 pm

Quote from kevman1 on August 28, 2025, 10:39 pm

 I can’t open the fusion file unfortunatly, my Fusion is crashing with unable to login error.

Here’s the stl file with a left and right one. I only use the right one for the battery and the other one as a balance (i put bullet casings of the same weight as the battery in there). It really helps with the overall stability of the car. I marked how long the screws are in the holes (i think i used these lengths)

Quote from kevman1 on August 29, 2025, 3:20 pm

Thank you , do you have the diff in STL format as well ? 

Quote from Sally on August 29, 2025, 7:09 pm

Quote from kevman1 on August 29, 2025, 3:20 pm

Thank you , do you have the diff in STL format as well ? 

Here are the Files for it. I made instructions for it as well but if you need any help my discord tag is: yescvnt