3D printable 1/10 RC Trophy Truck Chassis & Body Kit with Roll Cage STL files
Assembly Guide for 3D printed parts of RWD FORD F-150 “Baja” Trophy Truck.
Dimensions:
CHASSIS:
Wheelbase: 318 mm
Front Track: 222 mm
Rear Track: 230 mm
CHASSIS with BODY:
Width: 240 mm
Length: 533 mm
Height: 220 mm (LED on top)
Ford F-150 Chassis + Bodywork BOM
Bill of Materials (screws, washers)
DIN912 bolts
M3 nuts 119 pcs
M3x6 41 pcs
M3x8 32 pcs
M3x10 51 pcs
M3x12 2 pcs
M3x16 23 pcs
M3x20 30 pcs
M3x25 23 pcs
M3x30 7 pcs
M3x35 6 pcs
DIN7991 Countersunk screw with hexagon socket
M3x12 6 pcs
DIN913-Hexagon socket set screws with flat point
M3x16 2 pcs
M3x20 4 pcs
DIN125 Washer
Whaser for M3 bolts (D6,4mm) 4 pcs
Servo Screw
1 piece
Get the CHASSIS!
Get the BODY KIT!
NEEDED Parts
E-Motor 540
Electric Brushed (7.2 – 12 V, ~25.000 RPM)
GET it on:
Servo 01
Feetech FS5103B (40.8×20.1x38mm)
GET it on:
Motor Controller 01
QUICRUN 1060 (60A)(36.5x32x18.0mm)
GET it on:
Tire 01
48x30x98mm / 1.9×1.2×3.9 inch (Inner diameter X Width X Outer diameter)
GET it on:
10x15x4 Bearing
14 or 16 pcs needed
GET it on:
Suspension 02
Hole to Hole: 80mm 4 or 8 pcs
GET it on:
Battery 01
RC car LI-PO Battery 102x35x20mm 2200mAh. (Match up the connector with the motor controller’s!)
GET it on:
Pistol Grip Transmitter 01
6 channel radio transmitter with receiver
GET it on:
OPTIONAL Parts
Metal Differential 01
Metal Differential Gear for HSP 94122 94111 RC cars
GET it on:
Bewel Gear Inlet 01
Metal Inlet Gear of the Differential
GET it on:
Velcro / Rubber Band
Hook-and-loop fastener to fix the battery to the chassis (width 20 mm)
GET it on:
Printed Chassis Elements Assembly
1st step in the Assembly of Chassis nr. 3
The first assembly move will be the frontal frame of the Chassis. Two pieces need to be put together. Nuts are basic M3.
2nd step in the Assembly of the Chassis
Installing the servo into its bracket and setting up the steering system.
3rd step in the Assembly of the Chassis
Setting up gearbox housing with the electric motor.
4th step in the Assembly of the Chassis
Fixing the Trailing Arm Holders and the Middle Frame.
5th step in the Assembly of the Chassis
Assembling the central parts of the chassis.
6th step in the Assembly of the Chassis
Putting together the the Turn Buckles.
7th step in the Assembly of the Chassis
Fixing the two halfs of the Rocking Arms.
8th step in the Assembly of the Chassis
Fixing the Turn Buckles with the Rocking Arms to the Front Tower.
9th step in the Assembly of the Chassis
Fixing the suspensions to the front section.
10th step in the Assembly of the Chassis
Assembling Front Knuckles.
11th step in the Assembly of the Chassis
Fixing the knuckle to its place.
12th step in the Assembly of the Chassis
Attaching the Front Section to the Main Body Frame 01.
13th step in the Assembly of the Chassis
Attaching the Front Section to the Main Body Frame 02.
14th step in the Assembly of the Chassis
Attaching the Front Piece to the Front Tower to the Main Body Frame 02.
15th step in the Assembly of the Chassis
Assembling the Steering System 01.
16th step in the Assembly of the Chassis
Assembling the Steering System 02.
17th step in the Assembly of the Chassis
Assembling the Steering System 03.
18th step in the Assembly of the Chassis
Assembling the Rear Drive Chain with Fully Printed Parts.
19th step in the Assembly of the Chassis
Assembling the Rear Drive Chain with Ebay Metal Differential.
20th step in the Assembly of the Chassis
Fixing the Cardan Cup to the Gearbox.
21th step in the Assembly of the Chassis
Installing the Trailing Arms and the Rear Suspensions.
22nd step in the Assembly of the Chassis
Putting the Drive chain into its place.
23rd step in the Assembly of the Chassis
Fixing the Cardan Middle Piece to the side pieces.
24th step in the Assembly of the Chassis
Fixing the Cardan Shaft to the Cardan Cups.
25th step in the Assembly of the Chassis
Fixing of the Linking Arms.
26th step in the Assembly of the Chassis
Fixing the seats with single bolts.
27th step in the Assembly of the Chassis
Use a simple Rubber Band or Velcro.
28th step in the Assembly of the Chassis
Fixing the Motor Controller to the chassis.
29th step in the Assembly of the Chassis
Fixing the Battery: Use Rubber Band to fix the Battery to the long piece. Run through the bolts.
30th step in the Assembly of the Chassis
Do not forget to put the nuts into their places before threading the knobs.
31st step in the Assembly of the Chassis
Wheel Assembly.
32nd step in the Assembly of the Chassis
33rd step in the Assembly of the Chassis
Printed Body Kit Elements Assembly
1st step in the Assembly of the F-150 Body
Attaching the interior base to the Front Body Section. Please note M3 nuts to be used as well!
2nd step in the Assembly of the F-150 Body
Joining the Front and Middle pieces.
3rd step in the Assembly of the F-150 Body
Fixing the LED Roof Light
4th step in the Assembly of the F-150 Body
Rear Side pieces assembly and Taillight fixing.
5th step in the Assembly of the F-150 Body
Fixing the Rear Side pieces to the back Middle piece.
6th step in the Assembly of the F-150 Body
Snapping-in the Chase Lights
7th step in the Assembly of the F-150 Body
8 screws are holding the two halves of the body
Printed Roll Cage Elements Assembly
1st step in the Assembly of the F-150 Roll Cage
Assembling the pieces of the Front Section of the Roll Cage.
2nd step in the Assembly of the F-150 Roll Cage
Assembling the pieces of the Middle Section of the Roll Cage.
3rd step in the Assembly of the F-150 Roll Cage
Assembling the pieces of the Rear Section of the Roll Cage.
4th step in the Assembly of the F-150 Roll Cage
Joining the pieces of the Front and Middle Sections of the Roll Cage.
5th step in the Assembly of the F-150 Roll Cage
Joining the the two halves of the Roll Cage.
Printed Body Kit and Roll Cage Assembly
1st step in the Assembly of the F-150 Body and Roll Cage
Fixing the interiors to the Body Kit.
2nd step in the Assembly of the F-150 Body and Roll Cage
These parts can be snapped together. You might get way without gluing them together.
3rd step in the Assembly of the F-150 Body and Roll Cage
When the Roll Cage front is bolted, it also holds the grille in place.
4th step in the Assembly of the F-150 Body and Roll Cage
Fixing the frnt section of the Roll Cage.
5th step in the Assembly of the F-150 Body and Roll Cage
Joining the Roll Cage and Body at the Front Wheels.
6th step in the Assembly of the F-150 Body and Roll Cage
Joining the Roll Cage and Body at the Rear Wheels.
7th step in the Assembly of the F-150 Body and Roll Cage
For the final 3 steps assemble three knobs
You’ve just built an RC Trophy Truck!
Leave a Reply
You must be logged in to post a comment.